top of page

1962 FORD FALCON V8 AUTOMATIC

Description: Remove master cylinder, bench bleed master cylinder, remove all brake drums for visual inspection, right front wheel broken hardware, install a new one, adjust brakes, bleed brakes. Disassemble and paint front end parts, front end assembly, torque to spec, grease up, alignment, air pressure on tires, set, bleed brakes follow by Test drive.

​

1968 Ford Mustang

Description: Diagnostic, install power steering pump and hoses, replace strut bushing, power steering line, electrical, pinion seal, rear wheel seal. Remove and replace steering ram and valve.

1993 Chevy Corvette 40th Anniversary Edition

Description:

Diagnostic. Check injectors, test injectors, diagnose 8 bad injectors, verify fuel pressure, check fuel rail, return line clear. Install 8 new injectors, re-install fuel rails and return line clear; diagnose bad brake master cylinder, leaking at rear of m/c onto brake booster, install new master cylinder, bleed brakes, install alternator; test drive

1966 FORD Galaxy    

Description: Replace gas tank, sender installation, test sender; replace rear brake hose, transmission pan gasket, valve covers, sway bar links and bushing, strut rod bushings, add engine oil, power steering fluid, transmission fluid. Replace fuel line, install voltage regulator, heater hose. Rebuild, install and adjust carburetor, remove drums and check and adjust brakes. Hook up heat riser, make choke line. Install electric choke, new gas pedal cable follow by Test drive.

1978 INTERNATIONAL SCOUT

Description: Replace high pressure power steering line, replace output shaft seal transfer, case, transmission pan service. Install valve cover gaskets, clean, check front end, adjust idle follow by Test drive.

Parts replaced: transmission pan gasket and filter, power steering line, transfer case top off gear oil.

​

1974 TRIUMPH TR6

Description:  Check timing, check and sync carburetors, disconnect linkage, adjust idle, reconnect linkage, adjust choke, test drive: check for possible clutch/rotational noise-not currently evident. Test drive

1961 VW BUS, DUAL CARB WEBER

Description: Customer states that engine idles fast, perform engine diagnostic, compression check, set carbs, check timing, check and adjust valve lash.

1979 Lincoln Continental

Description:  Replace master cylinder, check rear brakes, test drive

1969 FORD F-100 TRUCK

Description:  Change fuel pump, adjust belts, change hose clamps.

1966 Ford Mustang 

Description: Diagnostic; remove plugs, distributor, (bad injector), reset timing, test drive. Installation of sniper and EFI. Test drive.

1972 TRIUMPH TR6

Description: Initial diagnostic; fix lights, install fuse block, install emergency flasher switch, check lights, install window regulator, install tank sender, fuel hose, clamps. Remove & replace radiator, fill with coolant; remove & replace tie rod ends; shop alignment, perform a brake review; check booster; check for fuel & water leaks, check speedometer. Wet sand & polish. Tune up, install master cylinder, bleed brakes. Test drive

​

1956 T-Bird

Description: Mechanical review of car with compression check, get running, remove carburetor, pack and send off to rebuild. Install carburetor, install sending unit, full deep cleaning. Test drive.

1962 FORD FALCON V8 AUTOMATIC

Description: Remove master cylinder, bench bleed master cylinder, remove all brake drums for visual inspection, right front wheel broken hardware, install a new one, adjust brakes, bleed brakes. Disassemble and paint front end parts, front end assembly, torque to spec, grease up, alignment, air pressure on tires, set, bleed brakes. Test drive.

​

1932 Ford Tudor Sedan

Description: Window assembly. Wet sand and polish body. Washed out radiator; get running, rebuild carburetor; fix driver door hinge; remove, paint and install horn; rewire headlights, replace battery; check lights; Install power switch. Test drive.

​

1966 Chevelle

Description: Diagnostic; burnt wires, install distributor, set time, install new engine harness; get running. Parts replaced: engine wiring harness, wire, distributor.

Assemble dash, clean up wiring, replace fuel tank; Wilwood brake installation; install coil and distributor, set timing, rebuild carburetor, install carburetor, install brake booster, bleed brakes, remake two rear brake lines, test drive; tuning of carburetor, check for leaks, set timing, set idle air, set idle; broken filler neck, install radiator.

Parts: wire holders, brake line rebuild kit. rear rubber brake hose, brake lines and fitting, valve cover breather. 

​